These commands create a view that includes all objects in the system group except for those in system. Use the snmp-server engineID local command for the local engine. A remote agent's engine ID must be configured before remote users for that agent are configured. User authentication and privacy digests are derived from the engine ID and user passwords.
The configuration command fails if the remote engine ID is not configured first. The snmp-server group command configures a new SNMP group. Members of SNMP groups are called users. The snmp-server user command allows a new user to be added an SNMP group and configures that user's parameters. The remote user is on the agent located at The snmp-server host command sets the community string if it was not previously configured.
This command adds a v2c inform notification recipient at The snmp trap link-change command enables SNMP link trap generation on the configuration mode interface. SNMP link trap generation is enabled by default. If SNMP link trap generation was previously disabled, this command removes the corresponding no snmp link-status statement from the configuration. The show snmp notification command displays the SNMP link trap generation information.
The snmp-server local-interface command specifies the interface from where an SNMP trap originates. The chassis ID string is typically set to the serial number of the switch. The SNMP manager uses this string to associate all data retrieved from the switch with a unique identifying label. Under normal operating conditions, editing the chassis ID string contents is unnecessary. The snmp-server chassis-id command configures the chassis ID string.
The default chassis ID string is the serial number of the switch. The show snmp command displays the chassis ID. This command configures xyz as the chassis-ID string, then displays the result. The snmp-server contact command configures the system contact string. The contact string is displayed by the show snmp and show snmp v2-mib contact commands.
These commands configure Bonnie H at as the contact string. The location string typically provides information about the physical location of the SNMP agent. The snmp-server location command configures the system location string. By default, the system location string is not set.
These commands configure lab as the location string. The following steps are mandatory when setting up the SNMP agent to send notifications:. The switch supports the execution of user supplied scripts to service portions of the OID space.
Startup and data collection overhead is required for each request. In both modes, the SNMP server is blocked from serving other requests when waiting for script responses. The snmp-server extension command configures the execution of user-supplied scripts to service portions of the OID space. Use the one-shot keyword to specify one-shot execution. This command specifies the file normal-example. This command specifies the file one-shot-example.
The first time the SNMP server requires a script result, it launches it with no arguments. Indicated errors by writing one of the error strings described in Set Request Error Strings In each case, the command should continue running.
The expected script response is the response varbind as three separate lines printed to stdout: the result OID, the type, and the value. If the command does not return an appropriate varbind, then the script should exit without producing any output. Normal Script Behavior indicates the type of the value passed as the third parameter. When the assignment is successful, the script exits without producing any output. Errors are indicated by writing just the error name Normal Script Behavior ; the agent generates the appropriate error response.
They may be enabled, like all traps, with the snmp-server enable traps command. In the above example, aristaMacAge traps are enabled, aristaMacLearn traps are disabled, and aristaMacMove traps have their default value, which is disabled. Continuing with the example from above:. The access-lists are reachable on the switch through the access SNMP data port The access-lists contain standard permit and deny commands.
When the VRF is not specified, default is assumed. Use the show snmp ipv4 access-list summary command to display an abreviated output of an IPv4 access-list. Use the show snmp ipv4 access-list detail command to display a detailed output of an IPv4 access-list. In this example, the configured access-list is Permit Use the show snmp ipv4 access-list summary command to display a summary of an active access-list. Use the show snmp ip access-list summary command to display a short output of the active access-lists.
The no snmp-server and default snmp-server commands disable Simple Network Management Protocol SNMP agent operation by removing all snmp-server commands from running-config. SNMP is enabled with any snmp-server community or snmp-server user command. The show snmp community command displays the Simple Network Management Protocol SNMP community access strings configured by the snmp-server community command. The show snmp group command shows the names of configured SNMP groups along with the security model, and view status of each group.
The show snmp mib command displays values associated with specified MIB object identifiers OIDs that are registered on the switch. Options include:. The show snmp notification host command displays information for Simple Network Management Protocol notification. The show snmp notification command displays the SNMP trap generation information. Use the show snmp notification grep bridge command to display the enabled or disabled status of each trap type.
Information that the command displays about each user includes their SNMP version, the engine ID of the host where they reside, and security information. The show snmp v2-mib chassis command displays the Simple Network Management Protocol SNMP server serial number or the chassis ID string configured by the snmp-server chassis-id command. The show snmp v2-mib contact command displays the Simple Network Management Protocol SNMP system contact string configured by the snmp-server contact command.
The command has no effect if a contact string was not previously configured. It includes the following sections:. Step 3 Scroll through the list to find the release you are interested in. This example is considered to be a trivial error and the MIB loads successfully with a warning message. The following example is considered as a nontrivial error even though the two definitions are essentially equivalent , and the MIB is not successfully parsed:.
If your MIB compiler treats these as errors, or you want to delete the warning messages, edit one of the MIBs that defines this same datatype so that the definitions match. Note To access this tool, you must have a Cisco. Follow these steps to download the MIBs onto your system if they are not already there:.
Any feedback is welcome! Many network devices and programs come with so-called MIB files that describe the parameters and readings that are available for monitoring via SNMP. MIB Importer Manual. MIB files are hardware and operating system—independent information files that tell network management systems how to retrieve in-depth data using the SNMP protocol from network devices like routers, switches, network printers, disk arrays even air conditioners as well as many server software products database servers, etc.
Because MIB files are written in this highly abstract definition language, they need to be translated into a more software-compliant form so that PRTG can work quickly and seamlessly with the data. MIB files are usually provided by the manufacturers of network devices and services for example, Cisco MIBs can be found here. Please visit your vendor's website or contact their support to get the MIB file for your specific device. Please understand that we cannot provide in-depth support for this program.
0コメント